LOTOS LTPAC2500 250A ACDC ALUMINUM TIG STICK PULSE WELDER 60A PLASMA CUTTER
93 • Power efficiency: 85% Accessories: • Larger 60A Heavy Duty Plasma cutting torch LP60 (13' 6") • Total 16 pcs plasma cutting consumables (Extra 5 tips, 5 electrodes and 3 shield cups, 1 tip, 1 electrode and 1 cup are pre-installed on cutting... ie=UTF8&showViewpoints=1 SPECS: Plasma Cutting • 220~240VAC, 50/60HZ • Duty Cycle: 60% at 60 amps and 100% at 45 amps • Rated Input Current: 31 amps • Rated Recommended Cut: 7/8" @ 10-12 IPM (inch per minute) • Rated Severance Cut: 1 1/8” @ 3 IPM... (Footpedal included in the package) Arc/Stick/MMA Welding: • Output Current: 15-200 Amps • Power Usage 20 Amps @ 220VAC • No Load Voltage: 62V • Can Weld: Steel, Stainless, Moly, Ferrous • Duty Cycle: 60% @ 250 Amps 100% @ 135 Amps • High... 6 CFM Tig Welding GTAW-P: • Output Current: 20-250 Amps • Power Usage 17 Amps @ 220VAC • No Load Voltage: 62V • Can Weld: Steel, Stainless, Moly, Ferrous • Duty Cycle: 60% @ 200 Amps 100% @ 105 Amps • High Frequency Start / HF Welding • Working... Type: 5-in-1 IGBT 60A Plasma Cutter and 250A AC/DC Aluminum TIG/STICK Pulse Welder with Footpedal (If you would like an AC/DC Aluminum Tig Welder ONLY (No plasma cutter), call us for a Special Deal) Condition: BRAND NEW (In Sealed Factory Box)... Cut at 12 Times the Speed of Sound Plasma Cutting is a process that is used to cut steel and other metals using a plasma torch. • Input Voltage: 200~250 VAC • Input Power Frequency: 50 hz / 60 hz (Better performance under 60 hz) • Insulation Grade: B • Housing Protection Grade: IP21 • Size: 247'' L x 20'' W x 15'' H • Weight: 70 lbs (78lbs with all accessories and... 9 Volts • AC balance control: 30% to 70% • AC Frequency Control: 20 to 100 Hz. • Gas Flow: 2-5L/min (using 100% Pure Argon supply, Argon Regulator and hose included) • Foot pedal fully adaptive (maximum current can be set by dial on pedal) -... The plasma is sufficiently hot to melt the metal being cut and moves sufficiently fast to blow molten metal away from the cut. (Note: for Aluminum AC Tig Welding, please use WT20,WZ08 or WP20 Tungsten electrodes. • 200 to 240VAC, DUAL Frequency ( 50Hz/60Hz ) • Robust Infineon (By Siemens) IGBT Power Drive Matrix • Brand new yet double function tested and performance tuned prior to shipping • PAPST cooling system from Germany • 5 Years Warranty on Parts and... Advantage of Plasma vs. Oxy-Fuel Torch Plasma does not use expensive, hazardous gases, only compressed air. ) CONTROL PANEL Accessories (Click to view FULL size image) Unrivaled Quality The production process for Lotos products is among the most stringent in the world and meets or exceeds some of the industry's most rigid standards. It helps you to easily achieve smooth, clean cuts of wide range of surfaces and material (e. g. stainless steel, alloy steel, brass, aluminum and other conductive material) with minimal heat input and without distortion of metal. and set the Pulse Current to "Minimum", Set "AC Balance to 50% , AC Frequency to 60HZ and Post flow to 12s. at the same time an electrical arc is formed through that gas from the nozzle to the surface that is being cut, turning some of that gas to plasma. The plasma, which is maintained between the work-piece and electrode, travels at over 9000 MILES PER HOUR (15,000 km/Handle). Lotos' latest high frequency inverter technology utilizes IGBT to deliver a far more constant, concentrated and precise current to the cutting surface. ADVANCED INVERTER TECHNOLOGY The LTPAC2500 inverter rectifies the input voltage (220VAC) into DC (Direct Current), which is then fed into a series of IGBTs. Skill and Training There is not a lot of skill or training required to operate a plasma cutter. The cost per cutting hour can be less than oxy-fuel since there is no gas cost. com/LTPAC2500-Aluminum-Welder-Plasma-Warranty/product-reviews/B0084KEMG6/ref=dp_top_cm_cr_acr_txt. Lotos Plasma cutters are designed especially for businesses and DIY (do-it-yourself) users, while fully accommodating the demands of professional operators. This technology has been substantially reduced in size and weight of Inverter Plasma Cutters. Only components and materials that meet the highest industry standards for quality are permitted to be incorporated into LOTOS products.